You are here: Forks > 32 mm > TALAS > TALAS FIT RLC

TALAS FIT RLC

Installing Your Fork | Before You Ride | Setting Sag | Adjusting Rebound | Locking Out the Fork | Adjusting Lockout Force | Adjusting Low-Speed Compression | Adjusting TALAS Travel | Service Intervals | Important Safety Information


travel

140 RLC: 5.5 in./140 mm
TALAS: 110 + 140 mm

150 RLC: 5.9 in./150 mm
TALAS: 120 + 150 mm

features/adjustments

TALAS 2-position travel adjust system, low-speed compression, lockout, lockout force adjust, air spring pressure, rebound

spring/damper type

air/FIT RLC

intended use

all-mountain, cross-country

Installing Your Fork

Be sure your fork is properly installed before proceeding. If your fork came pre-installed on your bicycle, continue to the next section.

Before You Ride

  1. Check that quick-release levers are properly adjusted and tightened.
  2. Clean the outside of your fork with only mild soap and water, and wipe dry with a soft dry rag.

    Note:  Do not use any solvents or de-greasers, as these products can cause serious damage to paint and anodized parts (upper tubes, knobs, steerers).

    Do not spray water directly on the seal/upper tube junction. Do not use a high pressure washer on your fork.

  3. Inspect the entire exterior of your fork. The fork should not be used if any of the exterior parts appear to be damaged. Contact your local dealer or FOX Racing Shox for further inspection and repair.
  4. Check your headset adjustment. If loose, adjust it accordingly to your bicycle manufacturer's recommendations.
  5. Check that all brake cables or hoses are properly fastened.
  6. Test the proper operation of your front and rear brakes on level ground.

Setting Sag

You can also view a Flash video on Setting Sag.

To get the best performance from your fork, it is necessary to set and adjust sag. Generally, sag should be set to 15 25% of total fork travel.

  1. Unscrew the center blue aircap in the middle of the TALAS travel adjusting topcap on top of the left fork leg (shown below), to expose the Schrader valve.

    Tip: Hold the TALAS lever steady with one hand while unscrewing the aircap with the other.

  2. Set the TALAS lever to the long travel position, turn off lockout and cycle the fork a few times.

    Note:  Always set sag in the long TALAS travel position. Sag and spring rate will automatically readjust when you change to different travel settings.

  3. Attach a FOX Racing Shox High Pressure Pump to the Schrader valve.
  4. Pump your fork to the appropriate setting from the Suggested Air Spring Pressure Settings table below, then remove the pump.
  5. Unless your fork already has a sag setting o-ring on an upper tube, install a zip tie to an upper tube. Slide the o-ring or the zip tie down against the scraper lip of the fork dust seal.
  6. Make sure your fork lockout is not engaged.
  7. Dressed to ride, position your bike next to a wall or table to support yourself. Without bouncing, mount your bicycle. Assume a normal riding position for at least 30 seconds, allowing the suspension to fully settle.
  8. Dismount your bike without bouncing downward, without further moving the o-ring or zip tie. Measure the distance between the seal and the zip tie. This measurement is your sag value.
  9. Compare your actual sag value to your target sag value in the Sag Setup table below.

    If your sag measurement value is less than the Sag Setup table value
    , screw on the pump fitting, note the current air pressure setting and depress the black bleed-valve to reduce the gauge pressure by 5 psi. Measure sag again and repeat this adjustment, if necessary.

    If your sag measurement value is greater than the Sag Setup table value
    , screw on the pump fitting, note the current air pressure setting and pump to increase the gauge pressure by 5 psi. Measure sag again and repeat this adjustment if necessary.
  10. Screw the blue aircap back on, and go ride.

    Rider
    Weight
    lbs.

    Suggested Air Spring Pressure Settings
    PSI

    140 mm

    150 mm

    ≤125

    50

    50

    125 - 135

    55

    55

    135 - 145

    60

    60

    145 - 155

    70

    65

    155 - 170

    75

    70

    170 - 185

    85

    80

    185 - 200

    95

    90

    200 - 215

    105

    100

    215 - 230

    115

    110

    230 - ≥250

    125

    120


    Sag Setup

    Travel

    XC/Race FIRM

    All-Mountain PLUSH

    140 mm (5.50")

    21 mm (0.81")

    35 mm (1.38")

    150 mm (5.90")

    23 mm (0.91")

    38 mm (1.50")


    Sag Troubleshooting

    Symptom

    Remedy

    Too much sag

    (+) air pressure in 5 psi increments

    Too little sag

    (-) air pressure in 5 psi increments

    Excessive bottoming

    (+) air pressure in 5 psi increments

    Harsh ride; full travel not utilized

    (-) air pressure in 5 psi increments

Adjusting Rebound

The rebound adjuster knob is located at the bottom of the right fork leg, as shown in the above figure. This knob has 18 clicks of adjustment range.

Rebound controls the rate of speed at which the fork extends after compressing. Turning the knob clockwise slows down rebound; turning the knob counter-clockwise speeds up rebound. As a starting point, turn the rebound adjuster knob all the way clockwise (full in) until it stops, then turn counter-clockwise (out) 12 clicks.


Knob Setting
(clicks out from full in)

Setting Description

Tuning Tips

Setup Tips

1

Slow Rebound

Too slow and your fork will pack down and ride harshly.

If you increase your spring rate or air pressure, you will need to slow down your rebound.

12

(Factory setting)

Average Rebound

18

Fast Rebound

Too fast and you will experience poor traction and wheel hop.

If you decrease your spring rate or air pressure, you will need to speed up your rebound setting.

Locking Out the Fork

The blue compression lockout lever, located just below the black lockout force adjuster knob, allows you to close the compression damping circuit in the fork. This keeps the fork at the top of its travel, making it harder to compress.

Note:  When you adjust the compression lockout lever, the black lockout force adjuster knob will also move. This is normal; the lockout force adjustment setting will not be affected.

Rotate the lever fully clockwise to lockout the fork. This position is useful in climbing and sprinting situations, but will sag with the rider’s weight. The fork will "blowoff" in the event that a big hit is encountered with the fork locked out.

To unlock the fork, simply rotate the lever fully counter-clockwise.

Note:  The fork may cycle a couple of times after enabling lockout. Once complete lockout is achieved, the fork may continue to move 3 - 5 mm. This is normal and does not affect performance.

Adjusting Lockout Force

Even when your fork is fully locked out, there are instances when you still want your fork suspension to be active. To protect your fork's internal parts, your FOX fork will "blowoff" when it encounters an intense hit. You can adjust when the fork blows off—lockout force—by adjusting the black knob on the right-side top cap.

A convenient tuning feature of the lockout force knob is that it allows you to leave your fork in the locked out position—no more fiddling with fork controls when the trail requires your undivided attention. Although you might need to adjust the knob a few times to find the sweet spot, once it is found you can simply leave your fork locked out. Your fork will then respond to hits in the trail for example, but will be locked out when you are out of your saddle on a climb.

Turn the knob clockwise to increase lockout force and counter-clockwise to decrease lockout force.

Note:  When you adjust the black lockout force adjuster knob, hold the blue compression lockout lever in place.

There are 10 clicks of adjustment. As a starting point, turn the knob all the way clockwise until it stops, then back off one click counter-clockwise.

Adjusting Low-Speed Compression

Low-speed compression damping is adjusted with the blue bezel ring that is positioned just below the blue lockout lever. This ring has 8 clicks of adjustment range. Compression damping controls the fork compression speed. Adjust the low-speed compression with lockout off (the lockout lever turned fully counter-clockwise). The factory setting is 8 clicks out counter-clockwise, from fully in clockwise.


Knob Setting
(clicks out from full IN)

Setting Description

Tuning Tips

Setup Tips

1

Firm Compression

Too firm and you will experience poor traction and wheel hop.

Resists brake dive and keeps the fork up in the travel. Too firm and you may have poor traction in loose conditions.

8
(factory setting)

 

 

8

Soft Compression

Too soft and your fork will pack down and ride harsh.

Maximum wheel traction and bump compliance. Too soft and you may have excessive brake dive and a wallowy feel.

Adjusting TALAS Travel

140 mm:
  • 5.50" (140 mm)
  • 4.33" (110 mm)
150 mm:
  • 5.90" (150 mm)
  • 4.75" (120 mm)

32 mm TALAS forks feature two externally-adjustable travel choices per fork travel specification. These travel settings are easily selectable with the TALAS travel adjusting topcap located on top of the left fork leg. Travel settings direction is clearly indicated on the topcap.

Note:  When changing travel, the TALAS system automatically adjusts to provide you with the appropriate linear air spring rate for each travel setting. There is no need to change the air pressure in the TALAS air chamber after adjusting travel.

CAUTION:  For safety reasons, adjust TALAS travel only when you're not riding the bike.



When It Counts.

When It Counts.


Bushing Technology & Inspection | Seals & Foam Rings | Control Direction | Oil Volumes | Structural Inspection | Dropout Thickness Inspection | Torque Values | Unit Conversion | Suspension Tuning Tips | Using the Pump | Important Safety Information | Service Intervals | Contact FOX Service | Warranty Information | FOXHelp Service Web Site


Copyright © 2011
FOX Factory Inc.