2021 36mm and 38mm Mud Guard Installation

Supplies Needed

  • 13mm Socket
  • 2.5mm Hex Wrench
  • 5mm Hex Wrench
  • Ratchet
  • Seal Pick
  • Torque Wrench

WARNING: FOX products should be serviced by a trained bicycle service technician, in accordance with FOX specifications. If you have any doubt whether or not you can properly service your FOX product, then DO NOT attempt it. Improperly serviced products can fail, causing the rider to lose control resulting in SERIOUS INJURY OR DEATH.

WARNING: FOX suspension products contain pressurized nitrogen, air, oil, or all 3. Suspension misuse can cause property damage, SERIOUS INJURY OR DEATH. DO NOT puncture, incinerate or crush any portion of a FOX suspension product. DO NOT attempt to disassemble any portion of a FOX suspension product, unless expressly instructed to do so by the applicable FOX technical documentation, and then ONLY while strictly adhering to all FOX instructions and warnings in that instance.

WARNING: Modification, improper service, or use of aftermarket replacement parts with FOX forks and shocks may cause the product to malfunction, resulting in SERIOUS INJURY OR DEATH. DO NOT modify any part of a fork or shock, including the fork brace (lower leg cross brace), crown, steerer, upper and lower leg tubes, or internal parts, except as instructed herein. Any unauthorized modification may void the warranty, and may cause failure or the fork or shock, resulting in SERIOUS INJURY OR DEATH.

img/help/page1054-WZEH/IMG_3645-m.jpg

Step 1

Position the front of the fork facing down on a clean work surface. Unthread the Pressure Release Button Assembly counter-clockwise from the lower leg with a 13mm socket. If you have Pressure Release Plugs unthread them counter-clockwise with a 5mm hex wrench. 

 

 

 

img/help/page1054-WZEH/IMG_3645.jpg
img/help/page1054-WZEH/IMG_3646.jpg
img/help/page1054-WZEH/IMG_3647.jpg
img/help/page1054-WZEH/IMG_3648.jpg
img/help/page1054-WZEH/IMG_3649.jpg
img/help/page1054-WZEH/IMG_3650.jpg


img/help/page1054-WZEH/IMG_3651-m.jpg

Step 2

Remove the Spacer from the Pressure Release Button or Plug Assemblies.

img/help/page1054-WZEH/IMG_3651.jpg
img/help/page1054-WZEH/IMG_3653.jpg
img/help/page1054-WZEH/IMG_3654.jpg


img/help/page1054-WZEH/IMG_3657-m.jpg

Step 3

Position the Mud Guard in place so the large holes align with Pressure Release ports and the small holes align with the threaded holes in the back of the lower leg brace. Reinstall the Pressure Release Buttons or Plugs by threading them clockwise. Tighten to 45 in-lb (5.0 Nm) torque.

img/help/page1054-WZEH/IMG_3657.jpg
img/help/page1054-WZEH/IMG_3658.jpg
img/help/page1054-WZEH/IMG_3661.jpg
img/help/page1054-WZEH/IMG_3659.jpg
img/help/page1054-WZEH/IMG_3660.jpg
img/help/page1054-WZEH/IMG_3662.jpg


img/help/page1054-WZEH/IMG_3665-m.jpg

Step 4

Thread the screws through the small holes of the Mud Guard into lower leg brace. Tighten clockwise to 4.5 in-lb (0.5 Nm) torque with a 2.5mm hex wrench.

img/help/page1054-WZEH/IMG_3665.jpg
img/help/page1054-WZEH/IMG_3666.jpg
img/help/page1054-WZEH/IMG_3667.jpg
img/help/page1054-WZEH/IMG_3668.jpg
img/help/page1054-WZEH/IMG_3669.jpg
img/help/page1054-WZEH/IMG_3670.jpg



Dealer, Distributor, and OEM access

Connect

Facebook Instagram Facebook Facebook
Worldwide   United States   Worldwide
External Bypass
Internal Bypass
Coil-over
Smooth Body
Air Shock
Bump Stop
Race Program
Contingency
Apply
By Type
Aluminum
Steel
 
By Class
Modified
Late Model
Sprint Car
Factory Race
Performance
Adventure
Conflict Minerals Policy
California Transparency in Supply Chains Act
United States
Worldwide
Press Releases
Events & Presentations
Corporate Governance
Financial Information
Stock Information
Investor FAQs
Contact Us