You are here: Rear Shocks > DHX > DHX RC2

DHX RC2

Installing Your Shock | General Maintenance | Before You Ride | Setting Sag | Changing Springs | Measuring Sag | Adjusting Rebound | Low Speed Compression (LSC) | Bottom-Out Control | Service Intervals | Important Safety Information


features/adjustments

low-speed compression (LSC), forged eyelets, increased shaft size, increased oil flow for increased tuning range, adjustable bottom-out force control via Schrader valve, coil spring preload, rebound adjust

spring

coil

intended use

competition downhill, freeride, all-mountain

Installing Your Shock

If you are installing your shock on a bike for which the shock is not original equipment:

  1. Install the shock with the spring retainer, but without the spring. (To remove the spring, read Changing Springs.)
  2. Carefully cycle the suspension through its entire travel.
  3. Check that all parts of the shock are clear of the frame and swingarm as it cycles through the travel.
  4. Properly place the spring back onto the shock.
  5. Set sag.

General Maintenance

Some things to consider:

Before You Ride

  1. Clean the outside of your shock with only mild soap and water, and wipe dry with a soft dry rag.

    Note:  Do not use any solvents or de-greasers, as these products can damage the shock's exterior finish or its anodized parts.

    Do not spray water directly on the seal/shock body junction. Do not use a high pressure washer on your shock.

  2. Inspect the entire exterior of your shock. The shock should not be used if any of the exterior parts appear to be damaged. Contact your local dealer or FOX Racing Shox for further inspection or repair.
  3. Make sure that your quick-release levers (or thru-axle pinch bolts) are properly adjusted and tightened.
  4. Check your headset adjustment. If loose, adjust it accordingly to your bicycle manufacturer's recommendations.
  5. Check that all brake cables or hoses are properly fastened.
  6. Test the proper operation of your front and rear brakes on level ground.

Setting Sag

To set sag on your DHX RC2:

  1. Measure sag, and compare it to the recommended sag setting shown in the Coil Spring Setting Guidelines table below. Continue if the sag is not to specification.
  2. Adjust the preload ring accordingly:

    If your sag value is less than the table value, turn the preload ring counter-clockwise. Always ensure that the spring is secure and does not freely move.

    Note:  After the preload ring engages the spring, turn the preload ring clockwise one turn. If the preload ring needs to be turned counter-clockwise from this point to achieve proper sag, you will need to obtain a lower rate spring.

    If your sag value is greater than the table value, turn the preload ring clockwise no more than two full turns after the preload ring engages the spring.

    Note:  If after the preload ring engages the spring and more than two full clockwise turns are needed to achieve proper sag, you will need to obtain a higher rate spring.

  3. Refer to bicycle manufacture’s manual for proper sag setting, for your specific model of bicycle. If there is no recommended setting available, refer to the Coil Spring Setting Guidelines table below.
  4. If necessary, contact FOX Racing Shox or an Authorized Service Center to obtain a higher or lower rated spring.

    Coil Spring Setting Guidelines

    Shock Travel
    (in./mm)

    Recommended Sag
    (in./mm)

    2.00/50.8

    0.66/16.76

    2.25/57.1

    0.74/18.79

    2.50/63.5

    0.83/21.08

    2.75/69.8

    0.91/23.11

    3.00/76.2

    1.00/25.40

    3.50/88.9

    1.16/29.46

Changing Springs

  1. Loosen the preload ring until the spring freely moves.
  2. Lift up the spring and remove the spring retainer.
  3. Slide the spring off the shock body. Depending on your bike model, you may need to remove the reducers to remove the spring.
  4. Orient the new spring correctly (see Spring Orientation below) and slide it onto the shock body.
  5. Place the spring retainer back on the shock and under the spring ensuring that the open slot on the spring retainer rests on the flat part of the spring end.
  6. Tighten the preload ring just until the spring no longer moves.
  7. Turn the preload ring one additional full turn.

Spring Orientation

When placing the spring back on the shock body, it is important that the spring is correctly oriented. Essentially, the space in the spring retainer should rest on the flat part of the spring, and not on the segment of the spring where it starts to coil back under itself. Rotate the spring or spring retainer until the correct orientation is achieved.

An improperly oriented spring can fail prematurely, causing loss of control of the bicycle, which can result in serious or fatal injuries. The pictures below demonstrate correct and incorrect spring orientation. Correct spring orientation applies to all FOX Racing Shox rear shocks that utilize coil springs:

Reading Your Spring Rate

Adjusting Rebound

Rebound controls the rate at which your shock returns after it has been compressed. The proper rebound setting is a personal preference, and changes with rider weight, riding style and conditions. A rule of thumb is that rebound should be as fast as possible without kicking back and pushing the rider off the saddle.

The rebound knob has approximately 15 clicks of adjustment.

For slower rebound, turn the red adjuster knob clockwise.

For faster rebound, turn the red adjuster knob counter-clockwise.

Low Speed Compression (LSC) Adjust


Turn the LSC adjuster clockwise with a flat screwdriver, to increase low-speed compression damping. The LSC adjuster primarily affects the compression damping during slow speed suspension movements, such as g-outs or smooth jump landings. It also affects wheel traction and harshness (or plushness) of your bicycle. The LSC adjuster has ~18 clicks of adjustment range.

Bottom-Out Control

Note:  The factory pressure setting for bottom-out control is 160 PSI.

For more information about using the Fox HP hand pump to adjust the bottom-out control air pressure, see Changing the Bottom-Out Control Pressure.

The bottom-out control valve provides position-sensitive end stroke damping; this allows for a seamless transition from small bumps to big drop bottom-outs. The bottom-out valve is not adjusted directly. Instead, its behavior and performance characteristics are influenced by the air pressure setting in the reservoir. To change the range of bottom-out control damping characteristics of your DHX RC2 shock, attach a FOX High Pressure Pump to the Schrader valve on the reservoir.


For more bottom-out resistance, add 10-15 pounds of air pressure, to a maximum of 200 PSI. For less bottom-out resistance, decrease the shock’s air pressure by 10–15 pounds with the pump’s bleed valve, to a minimum of 125 PSI. Ride your bike and verify the settings before repeating the procedure.

CAUTION:  Never ride your bike with more than 200 or less than 125 PSI in the reservoir air chamber. Doing so can damage your shock, requiring repairs that are not covered under terms of the warranty.

Note:  In racing applications, FOX Racing Shox uses nitrogen gas in the reservoir. For every day riding, air from the hand pump works fine; after all, it's ~78% nitrogen anyway.



When It Counts.

When It Counts.


Bushing Technology & Inspection | Seals & Foam Rings | Control Direction | Oil Volumes | Structural Inspection | Dropout Thickness Inspection | Torque Values | Unit Conversion | Suspension Tuning Tips | Using the Pump | Important Safety Information | Service Intervals | Contact FOX Service | Warranty Information | FOXHelp Service Web Site


Copyright © 2011
FOX Factory Inc.