Powersports Help Center

Here are some frequently used tuning tips for your suspension.
Don't see the tip you're looking for? e-mail us

Tuning for Conditions

Hard Pack Conditions
Generally adjust compression damping as soft as possible, to handle square edges while still having some control with bottoming.

Loamy Conditions
Adjust damping a little firmer for the loamy terrain, jump faces and bottoming. Optimum settings still should be on the softer side for square edges and rutted corners.

Sandy Conditions
Adjust damping towards the firmer side... increase your fork compression and increase your shocks rebound. In general, two (2) clicks each. You want the bike to ride on top of the terrain, allowing the forks to ride up a little higher.

Rocks and Roots Conditions
Adjust compression more towards the soft side of your baseline settings; this helps to absorb the small sharp hits. You can also speed up rebound both front and rear; this adjustment helps wheels react quickly from rock to rock. This will also produce a very soft plush feel and help reduce arm pump/fatigue. This type of setting is good for woods or trail riding, however it will not be firm enough for fast MX track conditions; the bike will have a wallowy feeling, and will have bottom out issues in woops and jumps.

Not using full travel, feels harsh, poor traction while making turns

Causes
Overly stiff springs or compression damping
Solutions
Reduce compression damping; softer coil springs

Bottoms, soft throughout travel

Causes
Spring rate too low throughout travel, or too little compression damping
Solutions
Increase compression damping; stiffer Coils Springs

Excessive sag, feels soft initially

Causes
Initial preload too low
Solutions
Increase spring preload

Harsh over small bumps but uses full travel

Causes
Initial spring rate or preload too high, too much compression damping
Solutions
Install softer springs; reduce compression damping; reduce spring preload

Takes first bump in a series well but harsh over later bumps, poor traction in washboard corners

Causes
Too much rebound damping
Solutions
Reduce rebound damping.

Too Much Compression

Symptom
Ride is harsh, but not as bad as too much rebound. As speed increases, so does harshness. Rear end will want to kick up when going over medium to large bumps (shock resist movement even on medium size bumps)
Solutions
Decrease compression until harshness is gone
Tip
To learn what damping can do for your ride, experiment with the compression adjustments and rebound adjustments. We suggest you start with compression damping. Turn the compression adjuster to full firm, ride your bike for a while, and then turn the adjuster to full soft. This will give you an idea what compression damping can do. Likewise do the same with your rebound adjusters; feel what fast rebound is like, feel what slow rebound is like

Wheel chatters over small bumps during braking or downhills

Causes
Too much preload, causing suspension to top out; possibly too much compression damping
Solutions
Reduce preload, decrease compression

Front end springs back too quickly after bumps, poor traction in bumpy corners

Causes
Not enough rebound damping
Solutions
Increase rebound damping

Rear Tuning tips

Tips
Compression damping, rebound damping. The spring preload sets the ride height of the vehicle, and determines how much of the total travel will be available for compression and how much will be available for extension. Damping keeps the vehicle from behaving like an old sacked-out Cadillac; i.e., still bouncing 10 seconds after hitting a bump. Compression damping slows the shock when it is being compressed. Rebound damping slows the shock when it is rebounding.

Not using full travel, feels harsh, poor corning and braking traction

Tips
An overly stiff spring rate or compression damping; possibly too much preload

Rear shock Lack of Compression

Causes
The rear suspension will feel too active (wallow excessively). On jump landings, the shock bottoms too easily.
Solutions
Increase the compression "gradually until the balance/feel is optimized". You will notice better bottom out control, and the wallow symptom will go away.

FOX glossary of terms

Coil Spring
Consists of a metal wire formed into a coil which can store energy when compressed, and releases energy as the load is relieved.

Compression Damping
The damping circuit that absorbs the energy of compression forces on the damper.

Damper
A fluid chamber with a means of regulating the fluid flow, to govern the speed of the moving end of the damper during compression or rebound strokes.

Damper Speed
The relative speed in which the moving end of a damper compresses or rebounds.

Damping
The process of absorbing the energy of impacts transmitted through the fork or rear shock on the compression stroke, and the process of absorbing the energy of the spring on the rebound stroke.

Damping Circuits
There are normally four damping circuits which affect the damper's speed. There is both a low and high speed circuit for the compression and rebound strokes.

HSC
High Speed Compression damping is the damping circuit in the shock absorber or suspension fork that is tuned to provide suspension travel control at high speed over square edged bumps. All Fox products are HSC tuned by extensive lab and field testing. Too low of HSC damping will cause excessive bottoming out in rough terrain. Too high of HSC damping will minimize suspension travel in rough terrain and cause loss of traction.

LSC
Low Speed Compression damping is the damping circuit in the shock absorber or suspension fork that is tuned to provide suspension travel control at low damper speed conditions. All Fox products are LSC tuned by extensive lab and field testing. Too low of LSC damping will cause the excessive travel use, brake dive and wallowing of the bike on small bump terrain. Too high of LSC damping will cause loss of traction on small bump terrain.

Suspension packing
A term used to describe the ride characteristics of a rear shock or fork that has too slow of a rebound setting. A damper with to slow of a rebound setting will stay compressed after hitting one bump and cannot rebound quickly enough to absorb the impact of the second or third bump. The solution is to adjust the rebound to a faster setting.

Preload
Preload is applied to the fork and shock springs in order to bring the bike to the proper SAG dimension. Adjusting preload to the proper SAG dimension insures traction as wheel load gets light and drops into bumpy holed sections of terrain.

Rebound Damping
The damping circuit that controls the stored energy release of the compressed spring, in order to reduce the rebounding speed of the damper.

SAG
To sink, droop, or settle from pressure or weight

Valve Shim
A thin, spring steel flat washer used to exert resistance on the oil flow through a piston. A series of valve shims (valve stack or valving) with varying outer diameters and thicknesses are arranged in sequence to provide a particular damping effect.

SLT (Scraper Lip Technology) Oil Seals
Patented scraper lip technology excludes outside dirt and retains internal fork oil. The rubber in the seal is specially compounded for extremely low friction and wear.

Spring Rate
Spring rate is described by force, in pounds or kilograms, needed to compress the spring one inch or centimeter.

Stiction
A combination of the words static and friction. This word is used to describe the tension exerted on the moving damper parts by the stationary parts like the bushings, seals, and wipers. Low stiction is more desirable, because it has less of a negative effect on the damping.

Un-sprung/Sprung Weight
The un-sprung weight of the motorcycle are parts like the wheels, brakes, swingarm and suspension linkage, and the lower front fork legs. The sprung weight is the sum weight of all the parts of the motorcycle that are supported by the suspension.



Register Your Product

I'm new
Create account
I have an account

Remember me   I forgot my password »
Log in

Connect

Facebook Instagram Facebook Facebook
FOX 40 Years
FOX 40 Years Bike Moto ATV Snowmobile UTV Truck Offroad
Worldwide   United States   Worldwide
EVOL Air Chamber
Kashima Coat
DSC
Rebound Damping
Position-Sensitive Damping
FLOAT Air Spring
Spring Preload
Race Reports
Articles
Events
BOC
F.A.S.T.
DSC
MX Compression Adjuster
Low Speed Compression
Spring Preload
Rebound Damping
Anti-Wallow Control (AWC)
Air Volume Adjustment (AVA)
By Type
Smooth Body
Coil-over
Bump Stop
Air Shock
Bypass
By Series
Factory
Performance
Race Program
Contingency
Apply
Events
Dual Speed Compression
Internal Bypass
FOX Ice Scraper Technology (FIST)
EVOL Air Chamber
Kashima Coat
DSC
Rebound Damping
Spring Preload
FLOAT Air Spring
By Type
Aluminum
Steel
 
By Class
Modified
Late Model
Sprint Car
By Type
Smooth Body
Coil-over
Bypass
Steering Stabilizer
Bump Stop
By Series
Factory
Performance
Adventure
 
 
By Make
Chevrolet
Dodge
Ford
GMC
Hummer
 
Isuzu
Jeep
Land Rover
Nissan
Toyota
Dual Speed Compression
Internal Bypass
Quick Adjust Bypass (QAB)
DSC
Kashima Coat
Bottom-Out Control
Internal Bypass
Rebound Damping
LSC
Conflict Minerals Policy
California Transparency in Supply Chains Act
All Races and Events
ATV Races and Events
Rip Off the Strip
United States
Worldwide
Press Releases
Events & Presentations
Corporate Governance
Financial Information
Stock Information
Investor FAQs
Contact Us