You are here: Rear Shocks > FLOAT > FLOAT R

FLOAT R REAR SHOCK

Installing Your Shock | General Maintenance | Before You Ride | Measuring Sag | Setting Sag | Adjusting Rebound | ProPedal Valving Options | Service Intervals | Important Safety Information | Stuck Down Shock | Air Sleeve Maintenance


features/adjustments

angled air valve, high volume standard air sleeve, lightweight chassis, factory-set ProPedal, air spring pressure, rebound adjust

spring

air

intended use

freeride, all-mountain, cross-country

Installing Your Shock

If you are installing your shock on a bike in which the shock is not original equipment:

  1. Install the shock.
  2. Remove the main air chamber air cap and let all the air out of the main air chamber.
  3. Carefully cycle the suspension through its entire travel.
  4. Check that all parts of the shock are clear of the frame and swingarm as it cycles through the travel.
  5. Pressurize your main air chamber to a minimum of 50 psi and no more than 300 psi. You will tune to a more specific air pressure in the Setting Sag section below.
  6. Set sag.

General Maintenance

There may be a small amount of air sleeve lubricant residue on the body. This is normal. If this residual air sleeve lubricant is not present, this is an indication that the air sleeve should be re-lubricated. Some other things to consider for all shock models:

Before You Ride

  1. Clean the outside of your shock with only mild soap and water, and wipe dry with a soft dry rag.

    Note:  Do not use any solvents or de-greasers, as these products can damage the shock's exterior finish or its anodized parts.

    Do not spray water directly on the seal/shock body junction. Do not use a high pressure washer on your shock.

  2. Inspect entire exterior of shock for damage. The shock should not be used if any of the exterior parts appear to be damaged. Please contact your local dealer or FOX Racing Shox for further inspection and repair.
  3. Check that quick-release levers (or thru-axle pinch bolts) are properly adjusted and tightened.
  4. Check headset adjustment. If loose, adjust according to manufacturer’s recommendations.
  5. Check that brake cables or hoses are properly fastened.
  6. Check that the front and rear brakes operate properly on flat land.

Setting Sag

You can also view a Flash video on Setting Sag.

To set sag:

  1. Measure sag, and compare it to the recommended sag setting shown in the Air Spring Setting Guidelines table below. Continue if the sag is not to specification.
  2. Locate the Schrader air valve on the shock and remove the air valve cap.
  3. Screw the FOX Racing Shox High Pressure Pump onto the air valve until the pump shows pressure on the gauge. Do not over-tighten.
  4. Add air pressure until desired pressure is shown on the gauge. Refer to the Air Spring Setting Guidelines table below for the proper sag setting.
  5. Unthread the pump from the air valve and measure sag.
  6. Repeat steps 2-5 until proper sag is achieved, then replace the air valve cap.

    Air Spring Setting Guidelines

    Shock Travel
    (in./mm)

    Sag
    (in./mm)

    1.50/38.1

    0.38/9.5

    1.75/44.4

    0.44/11.1

    2.00/50.8

    0.50/12.7

    2.25/57.1

    0.56/14.2

Adjusting Rebound

Rebound controls the rate at which your shock returns after it has been compressed. The proper rebound setting is a personal preference, and changes with rider weight, riding style and conditions. A rule of thumb is that rebound should be as fast as possible without kicking back and pushing the rider off the saddle.

The rebound knob has 8-10 clicks of adjustment.

For slower rebound, turn the red adjuster knob clockwise.

For faster rebound, turn the red adjuster knob counterclockwise.

ProPedal Valving Options

FOX Racing Shox and your bike manufacturer have teamed up to deliver a FLOAT R shock that has the perfect ProPedal tune for your bicycle’s rear suspension design.

Your FLOAT R is delivered to your bike manufacturer in one of three settings: FIRM, MEDIUM, and LIGHT.

The setting of your FLOAT R is listed on the band at the bottom of the air sleeve and is denoted by an icon, as shown on the left.

LIGHT is represented by the smallest bar.

MEDIUM is represented by the middle bar.

FIRM is represented by the largest bar.

The bar that is applicable to your tune will be highlighted and flanked on top and bottom with indicator arrows.

Changing your ProPedal tune can be done at an Authorized FOX Service Center for a nominal fee as it is not considered a warranty item.


WHEREVER YOU RIDE. WHEREVER YOU RIDE.


Bushing Technology & Inspection | Seals & Foam Rings | Control Direction | Oil Volumes | Structural Inspection | Dropout Thickness Inspection | Torque Values | Unit Conversion | Suspension Tuning Tips | Using the Pump | Important Safety Information | Service Intervals | Contact FOX Service | Warranty Information | FOXHelp Service Web Site


Copyright © 2010
FOX Factory Inc.